• Mail
  • Facebook
  • Twitter
  • Youtube
  • LinkedIn
  • Yelp
  • OK: 405-905-9175
  • FL: (850) 203-3239
Home Run Inspections, LLC
  • Home
  • About Us
  • Oklahoma Services
  • Florida Services
  • Your Inspection
  • Your Report
  • For Agents
  • Testimonials
  • Blog
  • Contact Us
  • Schedule Your Inspection
    • Schedule in Oklahoma
    • Schedule in Florida
  • Search
  • Menu Menu

Posts

Kick Out Flashing

June 14, 2016/0 Comments/in Blog, Spring Home Maintenance /by Scott Price

Kickout flashing, also known as diverter flashing, is a special type of flashing that diverts rainwater away from the cladding and into the gutter. When installed properly, it provides excellent protection against the penetration of water into the building envelope.

 

 

Several factors can lead to rainwater intrusion, but a missing kickout flashing, in particular, often results in concentrated areas of water accumulation and potentially severe damage to exterior walls. Water penetration into the cladding can occasionally be observed on the exterior wall in the form of vertical water stains, although inspectors should not rely on visual identification. There may be severe damage with little or no visible evidence.

Inspectors may observe the following problems associated with kickout flashing:

1.  The kickout was never installed.

  • The need for kickout flashing was developed fairly recently, and the builder may not have been aware that one was required. The increased amount of insulation and building wrap that is used in modern construction makes buildings less breathable and more likely to sustain water damage. Kickout flashing prevents rainwater from being absorbed into the wall, making it more essential than ever.

The following are locations where kickout flashing installation is critical:

  • anywhere a roof and exterior wall intersect, where the wall continues past the lower roof-edge and gutter. If a kickout flashing is absent in these locations, large amounts of water may miss the gutter, penetrate the siding, and become trapped inside the wall; and
  • where gutters terminate at the side of a chimney.


2.  The kickout was improperly installed.

  • The bottom seam of the flashing must be watertight. If it’s not, water will leak through the seam and may penetrate the cladding.
  • The angle of the diverter should never be less than 110 degrees.

3.  The kick-out was modified by the homeowner.

  • Homeowners who do not understand the importance of kickouts may choose to alter them because they are unsightly. A common way this is done is to shorten their height to less than the standard 6 inches (although some manufacturers permit 4 inches), which will greatly reduce their effectiveness. Kickout flashings should be the same height as the side wall flashings.
  • Homeowners may also make kickout flashings less conspicuous by cutting them flush with the wall, making them less effective.

In summary, kickout flashing should be present and properly installed in order to direct rainwater away from the exterior roof-covering materials, particularly at the chimney locations

Schedule Inspections Online at:

Home Run Inspections

Like us on FaceBook
Follow us on Twitter

 

Pages

  • About Us
  • Blog
  • Contact Us
  • Florida Services
  • For Agents
  • Home
  • Oklahoma Services
  • Pricing
  • Testimonials
  • Thank You!
  • Your Inspection
  • Your Report

Categories

  • Autumn Home Maintenance
  • Blog
  • Home Energy Efficiency
  • Home Inspections
  • Home Safety
  • Homeowner Tools
  • Inspection Day
  • Insurance Inspections
  • On-Going Home Maintenance
  • Perks
  • Spring Home Maintenance
  • Summer Home Maintenance
  • Uncategorized
  • Wind Mitigation
  • Winter Home Maintenance

Archive

  • February 2022
  • January 2022
  • December 2021
  • November 2021
  • July 2021
  • March 2021
  • February 2021
  • January 2021
  • February 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • August 2019
  • September 2018
  • August 2018
  • July 2018
  • February 2018
  • November 2017
  • October 2017
  • August 2017
  • July 2017
  • June 2017
  • May 2017
  • April 2017
  • March 2017
  • February 2017
  • January 2017
  • December 2016
  • November 2016
  • October 2016
  • September 2016
  • August 2016
  • July 2016
  • June 2016
  • May 2016
  • April 2016
  • March 2016
  • February 2016
  • January 2016
  • December 2015
  • November 2015

Home Run Inspections, LLC

We are an All-Star Team of Professional Inspectors providing Excellence in Inspection Services to Help You Assess & Maintain the Value of Your Real Estate Investments.

Oklahoma: (405) 905-9175

Florida: (850) 203-3239

Info@HomeRunInspections.com

Oklahoma Service Areas

Proudly providing inspection services to the OKC metro and surrounding areas from Guthrie to Purcell, El Reno to Shawnee, and everything in-between.

Oklahoma Service Areas

Florida Service Areas

Proudly providing inspection services to Walton County Florida & Surrounding Counties & Areas including Bay County, Okaloosa County, Holmes County, Washington County, Freeport, Defuniak Springs, Niceville, Santa Rosa Beach, Miramar, Destin, Fort Walton Beach, Navarre, Crestview, Pace, & More!

Florida Service Areas

Certified Master Inspector

Verify This Certified Master Inspector
© Copyright 2021 Home Run Inspections, LLC - Website by Spectora
  • Mail
  • Facebook
  • Twitter
  • Youtube
  • LinkedIn
  • Yelp
Scroll to top